With the patented dry®, interseal has developed a technically and . 8 x 8 x microns ( mils) dry equivalent to. microns ( mils) wet . Interseal Interthane SYSTEMS. COMPATIBILITY. Sep 22 , , SYNTHETIC ENAMEL PAINT, INTERSEAL HSALUMINIUM PART A EGA/20LT, Sri Lanka, Bangalore, LTR, , 35,,
|Published (Last):||14 November 2015|
|PDF File Size:||14.55 Mb|
|ePub File Size:||8.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances.
Interseal dries to form a non-tacky, tough, resilient temporary protective layer. Intercure HS is not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions.
A two component, low VOC, high solids epoxy, pigmented with aluminium to provide enhanced corrosion resistance.
Once units interseao paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Product Line Interseal 6. At low temperatures, it may be necessary to thin Intercure HS to enable airless apray application to be performed.
GTA Do not thin more than allowed by local environmental legislation Mix ratio: Intercure HS is suitable for application to blast cleaned surfaces which were initially to the above standard but have been allowed to intetseal under good shop conditions for up to days. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.
Over-application should be avoided as thick films will not be as good a substrate for topcoat adhesion after ageing as those at the specified thickness.
Low Temperature Curing 24 Hours 1. Warning Intercure HS is preferred for use with systems for chemical environments where zinc based materials can be subject to attack in both acidic and alkaline conditions. If oxidation has occurred between blasting and application of Intercure HS the surface should be reblasted to the specified visual standard.
Varnish Hybrid Water base. Be the first to write a review for this product! Intesreal high solids, low VOC, two component, high build, surface tolerant epoxy coating, Interseal HS provides excellent anticorrosive protection in industrial and offshore environments in both atmospheric exposure and immersion service. Absolute measured adhesion of topcoats to aged Intercure HS is 2111 than that to fresh material, however, it is adequate interseak the specified end use.
Search Import Export Data of India
Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Mouse over image to zoom. The surface may deteriorate to Sa2 standard but must be free from loose powdery deposits.
A low VOC, two component high ihterseal, high solids surface tolerant epoxy maintenance coating. Dry time 1 Hours 1 211 Hours 1 48 Hours 1 8 Hours 1.
Once the unit has been mixed, it must be used within the working pot life specified.
Interseal | Protective – Coatings – AkzoNobel
Thoroughly flush all equipment with International GTA However, if necessary, application over prefabrication blast primers can be performed. It is good working practice to periodically flush out spray equipment during the course of the working day. Work stoppages Do not allow material to remain in hoses, gun or spray equipment.
Over-application of Intercure HS will extend both the minimum overcoating periods and handling times, and may be intersfal to long term overcoating properties.
Suitable for overcoating within 7 hours in most climatic conditions hence speeding up production and throughput in fabrication shops. Zinc Phosphate version also available.
Systems compatibility Intercure HS will normally be applied to suitably prepared steel, e. A single component, spray applied, high build, water based coating for direct application over coated substrates and non-ferrous substrates.
Surface preparation All surfaces to be coated should be clean, dry and free from contamination.
This product is not available in pale and pastel shades due to a tendency to discolour rapidly. Available in colours as well as aluminium and glass flake versions with passivator, to provide additional anti-corrosive barrier protection.
As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges.